Fluke Corporation                                           MET/CAL Procedure
=============================================================================
INSTRUMENT:            Fluke 8062A: CAL ADJ /5100
DATE:                  13-Feb-95
AUTHOR:                Fluke Corporation
REVISION:              $Revision: 2.3 $
ADJUSTMENT THRESHOLD:  70%
NUMBER OF TESTS:       1
NUMBER OF LINES:       81
CONFIGURATION:         Fluke 5100B
=============================================================================
#
# Source:
#   Fluke 8062A instruction manual (P/N 632695, March 1982, Rev. 2, 3/93)
#
# Compatibility:
#   MET/CAL 4.0 or later
#
# Subprocedures:
#   None
#
# Required Files:
#   51_V8062.bmp
#
# System Specifications:
#   TUR calculation is based on specification interval of the accuracy file.
#   The default 5100B accuracy file contains 6 month specs.
#
# Fluke makes no warranty, expressed or implied, as to the fitness
# or suitability of this procedure in the customer's application.
#
# The 6 month specifications of the 5100B are used in TUR computations.
#
 STEP    FSC    RANGE NOMINAL        TOLERANCE     MOD1        MOD2  3  4 CON
  1.001  ASK-                                                              W
  1.002  HEAD         EQUIPMENT SETUP
  1.003  DISP         [32]                   WARNING
  1.003  DISP         HIGH VOLTAGE is used or exposed during the performance
  1.003  DISP         of this calibration. DEATH ON CONTACT may result if
  1.003  DISP         personnel fail to observe safety precautions.
  1.004  DISP         Ambient temperature: 21degC - 25degC.
  1.004  DISP         Relative humidity: less than 80%.
  1.004  DISP         Allow the UUT 30 min. to stabilize.
  1.005  DISP         NOTE: The top AC shield should remain installed on the
  1.005  DISP         instrument while the calibration adjustments are being
  1.005  DISP         performed. The positions of the trimpots and trimcaps
  1.005  DISP         are marked on the top AC shield along with a table
  1.005  DISP         summarizing the calibration procedures.
  1.006  DISP         The performance of the 8062A AC functions is affected
  1.006  DISP         by the capacitance between the main PCB and the bottom
  1.006  DISP         AC shield, which is dependent on the distance between
  1.006  DISP         them. The distance may vary, depending on whether the
  1.006  DISP         top cover is installed. To minimize performance
  1.006  DISP         variations, press down on the AC shield to simulate top
  1.006  DISP         cover installation while you perform the AC calibration.
  1.007  DISP         TURN ON UUT.
  1.008  HEAD         DC VOLTAGE CALIBRATION
  1.009  PIC          51_V8062
  1.010  DISP         Turn R6 fully clockwise (CW).
  1.010  DISP         Turn R5 fully counterclockwise (CCW).
  1.011  RNG          2V
  1.012  5100         1.9000V                                           S  2W
  1.013  DISP         Adj R6 (COARSE) for a reading between 1.9010 and 1.9025
  1.014  DISP         Adj R5 (FINE) for a UUT reading of 1.9000+/-0.0001V
  1.015  5100         *                                                 S
  1.016  RNG          200mV
  1.017  5100         190.0mV                                           S  2W
  1.018  DISP         Adjust R8 for a reading of 190.00+/-0.01mV
  1.019  5100         *                                                 S
  1.020  HEAD         AC VOLTAGE CALIBRATION
  1.021  DISP         Turn R18 fully clockwise (CW).
  1.021  DISP         Turn R15 fully counterclockwise (CCW).
  1.022  RNG          200mV                        AC
  1.023  5100         100.00mV                     200H                 S  2W
  1.024  DISP         Adj R15 (COARSE) for a reading between 100.40 and 100.95
  1.025  DISP         Adj R18 (FINE) for a UUT reading of 100.00+/-0.05mV
  1.026  5100         *                                                 S
  1.027  RNG          2V                           AC
  1.028  5100         1.0000V                      10kH                 S  2W
  1.029  DISP         Adjust C7 for a reading of 1.0000+/-0.0015V
  1.030  END